Quality Assurance & Engineering Support

Quality Built into Every Stage

Our quality focus spans the entire product and project lifecycle — from raw-material verification through production and fabrication to site installation and handover documentation.

Quality Assurance

Six Control Points, Raw Material to Site

Clima Tech’s quality focus spans the entire product and project lifecycle. A panel that leaves the factory correct can still fail on site if it is installed badly, so our checks do not stop at the loading bay.

Raw Material Verification

Incoming materials are checked against certified specifications before they enter production. Facings, chemicals and ancillaries all have to match what was approved.

Foam Density & Dimensional Control

Foam core density and panel dimensions are monitored throughout production. Density drives both thermal performance and structural behaviour, so it is watched continuously rather than sampled at the end.

Surface & Joint Quality

Surface finish, joint accuracy and sealant integrity are verified at each stage. Joint geometry is what determines whether the interlock or the fold performs as designed.

Thermal Performance Verification

Panels are tested to confirm thermal resistance meets design requirements — the number on the datasheet has to be the number in the product.

Duct Fabrication Quality

Fabricated ductwork is inspected for dimensional accuracy and sealing quality before it leaves for site, so rework does not land on the installation programme.

Site Installation Quality

On-site checks confirm that correct installation methods and support spacing have been applied, particularly at supports, penetrations and transverse joints.

Engineering Support

From Requirement to Installation

Our engineering team stays involved through the whole project, not just at the point of supply. Each stage below produces something you can use — a recommendation, a coordinated layout, a document for the file.

Stage 01

Requirement Review

We review project specifications, drawings, temperature conditions and performance requirements — including pressure classes, velocities and any hygiene or fire constraints that will govern selection.

Stage 02

Product Selection

We recommend the foam core, thickness, facing, jointing and installation system, and explain the trade-offs so the decision is yours and not a black box.

Stage 03

Technical Coordination

We coordinate duct routing, panel layouts, supports and site-specific conditions with your team, resolving clashes and constraints before fabrication starts.

Stage 04

Supply & Installation Support

We support fabrication planning, delivery sequencing and quality checks so that material arrives in the order your programme actually needs it.

Stage 05

Documentation & Handover

We provide datasheets, method statements, inspection records and project documentation for the handover file.

Engineers checking panel dimensions against specification on the production line
Production, fabrication and quality control at Shoolagiri SIPCOT, Tamil Nadu.

Submittals

Documentation You Can Put in the File

Test & Submittal Position

Fire, smoke, strength, water absorption and air-leakage claims are supported by the final third-party report for the relevant product. Technical values published on this site are current design data, subject to confirmation by final production testing and third-party certification.

Datasheets

Product datasheets issued against the approved specification for your project.

Method Statements

Current installation method statements for the site team to work to.

Inspection Records

Documented checks across fabrication and installation for the handover file.

Value Proposition

Why Partner with Clima Tech?

Focused Specialisation

Dedicated expertise in pre-insulated HVAC ducting, insulated panels and underdeck insulation.

Integrated Manufacturing & Engineering

In-house manufacturing with project-specific engineering support across all product options.

Project-Specific Selection

Recommendations matched to specification, site conditions and performance targets.

Responsive Support

Accessible commercial and technical support for consultants, contractors, developers and end users.

Quality & Support FAQs

What documentation do you provide?

Product datasheets, method statements, inspection records and project documentation at handover. For ENERMAX PIR™ we also provide suggested specification wording you can drop into a tender document.

Are your performance claims independently tested?

Fire, smoke, strength, water absorption and air-leakage claims are supported by the final third-party report for the relevant product. Technical values published on this site are current design data, subject to confirmation by final production testing and third-party certification. We will issue the relevant documentation with your submittal.

What is checked during production?

Incoming raw materials are verified against certified specifications before production. Foam core density and panel dimensions are monitored throughout the run. Surface finish, joint accuracy and sealant integrity are verified at each stage, and panels are tested to confirm thermal resistance meets design requirements.

Do you check installation on site?

Yes. On-site checks confirm that correct installation methods and support spacing have been applied, and fabricated ductwork is inspected for dimensional accuracy and sealing quality before enclosure.

When should we involve you in a project?

As early as possible — ideally at specification stage, before the duct schedule and pressure classes are frozen. That is when product selection can still influence weight, void depth, support design and programme. We are happy to review drawings at concept stage.

Bring Us in Early

The earlier we see the drawings, the more we can do about weight, void depth, support design and programme. Send us what you have.